SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Join
1991 Ford Crown Victoria LTD “MoneyVic”
Home/ Registry/ Ford/ LTD Crown Victoria/ “MoneyVic” supermotors.net/registry/4696

“MoneyVic”1991 Ford Crown Victoria LTD

46 photos documented since 2004 ♡ Follow this build

Photos

1991 Ford Crown Victoria LTD - Vehicle raised... yet again! 1991 Ford Crown Victoria LTD - Out she comes! 1991 Ford Crown Victoria LTD - It's out! 1991 Ford Crown Victoria LTD - After pulling the valve body and servos 1991 Ford Crown Victoria LTD - Pulling the pump 1991 Ford Crown Victoria LTD - Intermediate clutch pack, reverse drum, and forward drum are first out 1991 Ford Crown Victoria LTD - The infamous direct clutch drum... source of many problems for the multitudes! 1991 Ford Crown Victoria LTD - Empty case 1991 Ford Crown Victoria LTD - Take the fan off for easier cranking 1991 Ford Crown Victoria LTD - Dropped the driveshaft 1991 Ford Crown Victoria LTD - Removed the TC-flywheel nuts 1991 Ford Crown Victoria LTD - Removed the linkage from transmission 1991 Ford Crown Victoria LTD - Removed the linkage from transmission (other part) 1991 Ford Crown Victoria LTD - Removed cooling lines 1991 Ford Crown Victoria LTD - After valve body was removed 1991 Ford Crown Victoria LTD - Taking off the filter 1991 Ford Crown Victoria LTD - Taking off the valve body 1991 Ford Crown Victoria LTD - After getting the godawful governor ring off 1991 Ford Crown Victoria LTD - Governor removed 1991 Ford Crown Victoria LTD - Taking off the center support ring off 1991 Ford Crown Victoria LTD - De-clunk spring out 1991 Ford Crown Victoria LTD - Sun shell 1991 Ford Crown Victoria LTD - All the parts went in to two buckets of Parts Cleaner 1991 Ford Crown Victoria LTD - Pump 1991 Ford Crown Victoria LTD - Clutch drums hanging because I didn't break them down yet 1991 Ford Crown Victoria LTD - The token "all over the place" photo... the begin of the rebuild 1991 Ford Crown Victoria LTD - There are 6 sealing rings on the output shaft to replace... 2 orange (not shown) and 4 teflon (shown) 1991 Ford Crown Victoria LTD - The overdrive servo disassembled and ready to have new seals installed 1991 Ford Crown Victoria LTD - What putting new seals on the servo and clutch pistons look like. This is the majority of the actual act of "rebuilding"--installing new se… 1991 Ford Crown Victoria LTD - Forward drum and piston. This is after removing the large spring by way of the clutch spring compressore 1991 Ford Crown Victoria LTD - New seals for the forward piston 1991 Ford Crown Victoria LTD - Using the lip seal protectors to install the piston in the forward drum 1991 Ford Crown Victoria LTD - Using the spring compressor again to replace the large retaining spring. Yes, this is a pain 1991 Ford Crown Victoria LTD - The fun part! Putting new clutches and steels in... 1991 Ford Crown Victoria LTD - All the parts of the pump (save the stator half). Not a lot to it! Just some gears and a piston 1991 Ford Crown Victoria LTD - Using the seal protector to install the pump piston 1991 Ford Crown Victoria LTD - The stator half of the pump has 4 sealing rings, two are larger and two small 1991 Ford Crown Victoria LTD - The reverse clutch drum and piston 1991 Ford Crown Victoria LTD - Using lip seal protectors to install the reverse piston 1991 Ford Crown Victoria LTD - This is the intermediate sprag (also called the intermediate one-way roller clutch) that locks during 2nd gear, and it sits on top of the r…
Browse all 46 photos

The peanut gallery

No comments yet — be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot — the owner approves it onto the record.